Ways to make 30 inch bathroom vanity

No Comments ↓

1 Star2 Stars3 Stars4 Stars5 Stars (No Ratings Yet)

Connection pipes butt is totally unacceptable. Accordingly, if you need to connect two pipe segments, then it is done also with a special clutch. Valves – ball, but then again, soldered in plastic, also see picture on the right. For connection to the metal – tube with thick walls and a plastic thread. Practice shows that in the hot pipes threaded metal insert over time weakens, squeezed and there is a leak. Flooring is the best choice – granite. It is only slightly more expensive than tiles, which results in a small area of a dime, but it is much stronger and not slippery even with a smooth surface. Last in the 30 inch bathroom vanity bathroom is vital: fractures and traumatic brain injury slipping in the bathroom occupy the last place in a medical emergency by statistics.

When purchasing is sure to check the accuracy of the size and condition of the surface of the tiles: require the seller a few pieces of different packages. Refuses to – go to another. Put the tiles on end on a flat surface close to each other in pairs and rotating 90 degrees, look at the top edge. If you have 3-4 pairs of difference in the amount of less than 1 mm from the party can be taken after checking the “face” and glaze. Also putting mutually facing surfaces of tiles to each other. Visible to the eye hillock, “trough” or “propeller” should not be. Then take a tile tray close your eyes and look along its surface against the light. There are dots, cracks, micro rainbow – Culling: in the bathroom soon will acquire dirt and to clean.

Such high demands on the tile for the 30 bathroom vanity due not so much aesthetic as hygiene: the invisible eye of pollution become a hotbed of the spread of infection and a bath and monitor the condition of the surface and wash it hard. Therefore the options “alternative” products better and did not consider.

Clay tile is better to take slow drying – 12-24 hours. When self-installing it will run slowly and remove blemishes without compromising the quality of coverage. In the first place again Hygiene tile can still firmly hold on, but in a tiny shell underneath microbes find their cozy and inaccessible to your abode.

READ  Seven innovation of design of a bathroom in farmhouse

Materials for 30 bathroom vanity with top

Spatula glue should be chosen with the pitch and depth of the teeth, indicated on the packaging glue. If no such instructions, and this glue previously tested and proven to be reliable, the teeth – from 3 to 6 mm. Coarsely toothed spatula for gluing floor will give too high a rusty glue and a tile will surely cavity. Immediately care and a crowned with a diamond drill at the outer diameter of the pipes purchased. Templates for laying tiles – plastic crosses, with other work in the 30 bathroom vanity with top will be difficult. About trowel for grouting cannot worry:

  • Instead go perfectly scrap the electric boiler with a diameter of 5-6 mm Vinyl insulated, see below. But be sure to stock up on flannel cloth (for the same grout), and it is better to buy cheap micro fiber discs 5-6 wipes for cleaning glasses.
  • Other materials for the repair of the bathroom are selected by the usual criteria for construction works. Room preparation first of all you must decide what to do with the old bathroom.

If cast iron – it is better to leave and refurbish epoxy or acrylic compound. If the tin, but without chipping enamel and somehow embedded fistula, then the best solution is to install an acrylic liner. Well, the “dead tin” is better to pass on scrap acrylic and put instead. New cast iron in quality and durability is not much better, and it will have to roll over and straining at the risk of damaging the newly laid decor. Next, disable the water; disconnect the pipe after the cold tap in the cistern and the kitchen are forwarding makeshift, at least from garden hose irrigation. Sitting completely without water for at least 10 days, that’s for sure. One need only remember the night or leave the house to block bends of risers: the hose has a hose. Then, from the 30 inch bathroom vanity with top to remove all the bare walls. Sewer is not touch. Heating pipes, sockets, suitable choke screw plugs. Bathroom vanities 30 inch disable wiring in the junction box; for lighting during operation will have to use a portable lamp on the extender.

READ  How to make one day bathroom remodel?

The panel building some projects you can expect a “nice” surprise inside insulated box of GWP (gypsum fiber boards). It certainly must be removed; you see the seamy side plates and crate – will understand why. The work is added, and the ceiling is necessary to work carefully, to expose the backup, so as not to hit. Old tiles bring down the hammer with a chisel concrete. If the tile was laid in cement mortar, have to tinker: its residues should not be.

Paintings in 30 inch bathroom vanity with top

The paint and the top layer of plaster remove the drill from the round metallic brush of 80-100 mm; this is the dustiest and nasty piece of work, so it is desirable home somewhere rid of, and the bathroom door firmly shut, or if already removed, tighten its opening film. Otherwise returning households, as they say in Odessa, you will have something to listen to. And what to buy again, especially furniture and carpets. Suddenly the old plaster will be loose and unstable (in older homes – most often), remove it to a concrete or brick walls. If lucky, and durable – align drill with sweep brush, checking the level. Gimp is a lot, but in the future it will reimburse. The plaster on the wiring obovate hammer with a chisel (do not forget to turn off in the distribution box or on a guard!) And remove the wires.

Revision floor cement substrate remains under the tile from the floor to remove the hammer chisel. If there is reason not to touch the old screed (for example – once completely drained washed, and the neighbors are not leaked a single drop), it is better to use the grinder with a diamond cup (cup-shaped Ladder points circle). Tool expensive for 30 inch bathroom vanities, but further work will pay off with a vengeance. This is followed by careful wet cleaning and careful inspection of the old ties. A crack is a major overhaul with the replacement of floor covering, or pouring a liquid balancer. Last on the final cost of money, labor and time, optimally, except when is or will be installed cast iron bath – its weight of water is larger than allowed.

READ  10 Ideas for small bathroom designs


If the repair is carried out in a bath, the variant is self-leveling floor is doubly attractive: for a tiny room costs even on the road Thermal Plats will be negligible compared with the general, and the equalizer can be poured directly over the old tiles. And we immediately get warmed floor. A layer of self-leveling floor based upon solidification shrinkage of 10% should be less than 30 mm; necessary, its volume is determined from this calculation.


But in any case it needs a new floor waterproofing. Use Waterproofing for waterproofing in the bathroom cannot be an ordinary film. Not for nothing because in relation to the bathroom vanity 30 saying “waterproofing” and not “steam isolation”. There is no alternative material – anteroom or analogs of polyester (PET). If the bag of a film pours water, tie it and hang in July in the heart of the desert, in a month the water will not be lowered. Waterproofing joints or glued with special mastic or welded industrial hairdryer. The latter requires skill, so you first need to be trained on the pieces. Plant for isolation walls are not less than 25 cm (4000 l of water spilled on 10 sq. m; overlapping strength by weight) with folds (without cuts!) At the corners. After lying the insulation can be poured floor or make a new tie.



Leave a Reply

Your email address will not be published. Required fields are marked *

Read previous post:
7 advices to make repair with 24 inch bathroom vanity

Make design your own bathroom

7 great ideas for handicap bathroom design